Tungsten carbide blade for cutting aluminum

Product Introduction

Application

Parameter Table

Product Introduction

Our high-quality Tungsten carbide saw blades are featured by precise cutting size, smooth cutting surface, high efficiency, long service life, impact resistance, and so on.

And our Tungsten carbide saw blade is widely used in cutting the wood, wood-based panel, plastic, and aluminum alloy, which is a professional and ideal cutting tool and get good feedback from the new and old customers in different countries.

Application

Used for pushing table saw, automatic saw and precision saws and special machinery.

Parameter Table

OD (mm)	Teeth Number	Thickness (mm)	ID (mm)	Teeth Shape
205	80	2.5	25.4/30	Flat teeth
205	100	2.5	25.4/30	Flat teeth
230	80	2.8	25.4/30	Flat teeth
230	100	2.8	25.4/30	Flat teeth
255	80	3	25.4/30	Flat teeth
255	100	3	25.4/30	Flat teeth
255	120	3	25.4/30	Flat teeth
305	80	3	25.4/30	Flat teeth
305	100	3	25.4/30	Flat teeth
305	120	3	25.4/30	Flat teeth
355	80	3.5	25.4/30	Flat teeth
355	100	3.5	25.4/30	Flat teeth
355	120	3.2	25.4/30	Flat teeth
405	80	3.5	25.4/30	Flat teeth
405	100	3.5	25.4/30	Flat teeth
405	120	3.5	25.4/30	Flat teeth
450	80	4	25.4/30	Flat teeth
450	100	4	25.4/30	Flat teeth
450	120	4	25.4/30	Flat teeth
500	80	4.5	25.4/30	Flat teeth
500	100	4.5	25.4/30	Flat teeth
500	120	4.5	25.4/30	Flat teeth
600	120	5	38	Flat teeth
600	144	5	38	Flat teeth
700	120	5.5	38	Flat teeth
700	144	5.5	38	Flat teeth
800	144	6,0	38	Flat teeth
900	144	8	38/50	Flat teeth
1000	144	8	38/50	Flat teeth

Attention To Points Of Use

1. Operating Conditions

Machine cover is essential to minimize the injuries by flying broken blades.Irrelevant people are not allowed in the work shop.Flammables and explosives should be kept away from the work floor.

2. Safety Measures

Wear glasses when working, to prevent from injuries by broken blades.Watch out for your ties and sleeves. Long hair should be kept inside the cap. and no gloves are allowed during operation.

3. Before Use

Ensure the machines are in good condition with no deformation and no spindle vibration,The spindle' s running tolerance can be h7.Make sure the blades are not excessively worn-out,blade body has no defomation or breaks lest injuries occut. Make sure appropriate saw blades are used.

4. Installation

Ensure the saw blade turns in the same direction as the spindle does. If not,accidents are likely to occur.

Choose the flange whose inner diameter is the same as that of the saw blade but the outer diameter is a little larger than 1/3(for multi-rip saw blade is 1/2) of the saw blade.

Ensure the flange is clean,not over, worn,bent and distorted shape.Check the tolerance between the saw blade and the spindle. Install the flange and fasten the screw.

Be sure no people stand in front of the machine when starting the machine.Do not feed,just to check whether there is any vibration,radial or axial run out.

Saw blade reprocessing such as bore trimming or reboring, should be finished by the factory . Poor processing would lead to poor quality and may cause injuries.

While installation, the saw blade should be 5- 6 teeth higher than the board surface.

5. In Use

In operation wood materials should be properly fixed lest abnormal cutting occurs.The operation must be stopped rightly once unusual noise and vibration occurs,if not,rough surface and tip-breaking may occur.

6. After Use

Saw blades should be resharpened because dull saw blades may affect cutting effect and lead to accidents.Resharpening should be made by professional factories,not changing the original angle deg